警告與準備 ：

　　Warning and Preparation:

　　非本機操作手或未經授權的其他操作手禁止開啟機器。

　　Non local operators or unauthorized operators are prohibited from turning on the machine.

　　檢查過程中發現設備存在安全隱患的禁止啟動設備。

　　During the inspection process, if any safety hazards are found in the equipment, it is prohibited to start the device.

　　開機前檢查開齒盤是否清潔，機器各部件是否運轉自如。

　　Before starting up, check if the gear plate is clean and if all parts of the machine are running smoothly.

　　檢查托輥是否與型材底部形狀吻合。

　　Check if the roller matches the shape of the bottom of the profile.

　　手送型材進入機器，調整開齒盤至型材齒槽中間，按工藝要求壓入適當深度。

　　Hand feed the profile into the machine, adjust the toothed disc to the middle of the profile groove, and press it into the appropriate depth according to the process requirements.

　　調整各導向輪，確保型材運動方向與齒盤接觸點運動方向一致。

　　Adjust each guide wheel to ensure that the direction of movement of the profile is consistent with the direction of movement of the contact point of the gear plate.

　　注意電氣開關是否指向OFF。

　　Pay attention to whether the electrical switch is pointing to OFF.

　　開機與試運行 ：

　　Startup and trial operation:

　　調整后，可先試一段型材，用隔熱條檢查是否合適。

　　After adjustment, you can first test a section of the profile and use insulation strips to check if it is suitable.

　　按下啟動按鈕正式開機工作。

　　Press the start button to officially start working.

　　啟動開齒機進行加工，注意觀察加工過程中的異常情況，如異常聲響、振動等，及時停機檢查。

　　Start the gear opening machine for machining, pay attention to any abnormal situations during the machining process, such as abnormal sounds, vibrations, etc., and stop the machine for inspection in a timely manner.

　　操作注意事項 ：

　　Precautions for operation:

　　開齒機應由專人使用和保養。

　　The gear opening machine should be used and maintained by a dedicated person.

　　注意電機和減速機的溫升，如溫升超過20℃，應停機檢查潤滑是否良好。

　　Pay attention to the temperature rise of the motor and reducer. If the temperature rise exceeds 20 ℃, stop the machine and check if the lubrication is good.

　　工作時不可戴手套，注意保持機內清潔。

　　Do not wear gloves while working, pay attention to keeping the inside of the machine clean.

　　開機時不可用手接觸正在運動的型材，以免受傷。

　　Do not touch the moving profile with your hands during startup to avoid injury.

　　維護保養 ：

　　Maintenance and upkeep:

　　每天清潔機器。

　　Clean the machine every day.

　　每月用30號的油潤滑主軸。

　　Lubricate the spindle with oil on the 30th of each month.

　　每六個月用30號的油潤滑彈簧螺母。

　　Lubricate the spring nut with oil on the 30th every six months.

　　其他安全事項 ：

　　Other safety precautions:

　　禁止在未經培訓或未熟悉開齒機操作的情況下進行操作。

　　It is prohibited to operate the gear opening machine without training or familiarity.

　　禁止在機器運轉時觸摸或調整刀具和夾具。

　　Do not touch or adjust tools and fixtures while the machine is running.

　　禁止在加工過程中離開工作崗位或進行與工作無關的活動。

　　It is prohibited to leave the workplace or engage in activities unrelated to work during the processing.

　　禁止在酒后或疲勞狀態下操作開齒機。

　　Do not operate the gear opening machine under the influence of alcohol or fatigue.

　　注意危險區域標識，避免進入或靠近危險區域，如刀具旋轉范圍、切屑飛濺區域等。

　　Pay attention to the hazardous area markings and avoid entering or approaching hazardous areas such as tool rotation range, chip splashing area, etc.

　　本文由AB面雙頭開齒機提供幫助，更多的相關內容請點擊：http://m.mmssii.com希望本文能夠為您帶來幫助，感謝您的閱讀！

　　This article is assisted by the AB surface double head gear opening machine. For more related content, please click: http://m.mmssii.com I hope this article can be helpful to you. Thank you for reading!